• Permit flows in one direction and close automaticaly if flow reverse size.
• Low wieght and short laying length saves initial cost, requires less space, and is easier to install. 
• Independent springs provide quick-closing, non-slam shut off for reduced water hammer potential.
• Lightweight, spring-loaded discs have low cracking pressure for energy efficient operation.
• 200 Micron Fusion Bonded Epoxy Powder Coated internal and external ensured barrier to corrosive chemicals, moisture and humid air. 
•  Featuring dual lightweight discs, responsive independent springs and a durable resilient seat for reliable flow activated operation with tight sealing and reduced water hammer potential. 
• EPDM rubber seat to facilitate quiet/Silent operations and improve disc seating without any leakage.

• Permit flows in one direction and close automaticaly if flow reverse size.  
• Low wieght and short laying length saves initial cost, requires less space, and is easier to install. 
• Independent springs provide quick-closing, non-slam shut off for reduced water hammer potential. 
• Lightweight, spring-loaded discs have low cracking pressure for energy efficient operation. 
• 200 Micron Fusion Bonded Epoxy Powder Coated internal and external ensured barrier to corrosive chemicals, moisture and humid air. 
• Featuring dual lightweight discs, responsive independent springs and a durable resilient seat for reliable flow activated operation with tight sealing and reduced water hammer potential. 
• EPDM rubber seat to faciliate quiet/Silent operations and improve disc seating without any leakage.

• Permit flows in one direction and close automaticaly if flow reverse size. 
• Low wieght and short laying length saves initial cost, requires less space, and is easier to install.
• Independent springs provide quick-closing, non-slam shut off for reduced water hammer potential. 
• Lightweight, spring-loaded discs have low cracking pressure for energy efficient operation. 
• 200 Micron Fusion Bonded Epoxy Powder Coated internal and external ensured barrier to corrosive chemicals, moisture and humid air. 
• Featuring dual lightweight discs, responsive independent springs and a durable resilient seat for reliable flow activated operation with tight sealing and reduced water hammer potential.
• EPDM rubber seat to faciliate quiet/Silent operations and improve disc seating without any leakage.

• Permit flows in one direction and close automaticaly if flow reverse size. 
• Low wieght and short laying length saves initial cost, requires less space, and is easier to install. 
•  Independent springs provide quick-closing, non-slam shut off for reduced water hammer potential. 
• Lightweight, spring-loaded discs have low cracking pressure for energy efficient operation. 
• 200 Micron Fusion Bonded Epoxy Powder Coated internal and external ensured barrier to corrosive chemicals, moisture and humid air. 
• Featuring dual lightweight discs, responsive independent springs and a durable resilient seat for reliable flow activated operation with tight sealing and reduced water hammer potential. 
• EPDM rubber seat to faciliate quiet/Silent operations and improve disc seating without any leakage.

• Double regulating feature allow the valve to be used for isolation to be re-opened to its pre-set position to maintain required flow rate. 
• Built-in measuring nipple (test point 3mm) for flow measurement based on Kv metholdology. 
• Has sufficient authority to regulate flow in circuit incorporating the flow measuring device. 

INSTALLATION

Always install the valve with the arrow on the body in the Same direction of flow. In order to avoid turbulence, which will effect the measuring accuracy, it is recommended to have a straight length of pipe up and down stream from the valve as shown (D-diameter of pipe)

• Double regulating feature allow the valve to be used for isolation to be re-opened to its pre-set position to maintain required flow rate. 
• Built-in measuring nipple (test point 3mm) for flow measurement based on Kv metholdology. 
• Has sufficient authority to regulate flow in circuit inc

INSTALLATION

Always install the valve with the arrow on the body in the Same direction of flow. In order to avoid turbulence, which will effect the measuring accuracy, it is recommended to have a straight length of pipe up and down stream from the valve as shown (D-diameter of pipe)

• The unit allows regulating ,flushing & isolating operations. 
• Fully ready mounted product,fast installation connection.
• Flexible connections,the whole assembly can be adjusted in site for maximum convenience & easy accessibility with the space available
• Minimum Commissioning only to pre-set flow rate for control valve(PIBCV)after installation of the systems.
• Possible to set all positions,excellent  for insulation,possibilities for flushing through PIBCVs due to hollow cone design.
• Factory pressure tested at 30 bar certified by 3rd party. Optimizing the variable Flow Systems to give maximum Comfort & minimum energy consumption.
• Minimum design, easy selection & very compact design for easy installations. Strainer With drain valve for easy draining eliminates opening of strainer plug.
• BSRIA teated for PIBCV's on performances at part load conditions for all sizes.
• Strainer are with 20MESH

• Minimum condensation due to maximum rapport with ?ow mate. 
• Easy installation & minimum workmanship. 
• Made speci?cally for the FCU Link Flow mate. 
• Standard in dimension and design for all Flow mates. 
• Suitable with ambient temperature. 
• Hermetic to moisture. 
• Constrict proof. 
• Reserve model EPP insulation.